|
How to Wind Toroidal Mobius Coils |
 |
 First
- Make yourself a "mobius Cable" to wind the coil from. While you
can wind a mobius coil from single strands of wire, it certainly
seems to be a lot more potent when you use a cable made in the
manner described here to wind the coil from. Take a length of wire,
and double it back on itself twice as shown to the right. Pull a
little slack out at the ends of the wire, this will be the leads of
the coil when it is finished. You should leave yourself at least 2"
for leads, and it is a good idea to give yourself 6" or so, you can
always trim the leads to the required length when the coil is
finished. It is much easier to use a drill to twist the wires than
doing it by hand. After experimenting with both CW and CCW coils, we
have discovered that either will work. For many, a CCW coil is more
comfortable. Not shown in the picture above is how to fit the cable
end into the drill. Before inserting the cable end into the drill to
twist it, fold the leads back so that they point towards the end of
the cable opposite the end with the leads. Then wrap a few turns of
electrical tape around the wires to protect them from the drill. Use
about 5 or 6 turns of electrical tape. This provides a cushion so
that when you tighten the drill chuck on the wires, it will not
scrape off the insulation. While working with the coil, be careful
not to scrape the insulation off the wires, or the coil will short
out and not work.
-
Starting with the end of the cable which does
not have the leads, make a circle in the clockwise direction
about the size you want your finished coil to be. You can wind
the coil around a core (xtal for your SP) or you can wind the
coil by itself if you are using stiffer wire.
- When you complete the first wrap, feed the wire through the
center of the circle so it wraps around itself in the clockwise
direction as shown. Use a little glue (hot melt or silicone
preferable) to hold the wire in place where it crosses over
itself.
- Continue winding the wire around the circle again.
- Go around the circle about one third of the way, and wrap
the cable around itself again, just like in step 3. Go around
the circle another third of the way, and do the same thing
again. You should have 3 wraps around the cable for each time
you go around the circle.
- Continue this way, repeating step 4, until you have used up
all of the cable. As shown to the right, stay on the same side
of the previous wrap with each new revolution. The 'knots' will
run together.
When you are finished, use a little glue to hold the end of the
cable in place. The coil should look like this when you are
finished.
Just keep wrapping the cable around itself (clockwise) as you go
around the circle. With a little practice, you will find that the
windings form a pattern, and if you make a mistake it will be
obvious as it does not fit the pattern. This coil tends to hold its
shape better than the single knot style, and I generally just wind
it by itself, not on a core. You should measure the diameter of the
object you wish to place in the coil as a core when it is finished,
and start with a circle a little larger than the diameter of the
intended core.
We recommend using a Quartz, 'Moquis Marble', or Kyanite core for
mobius coils, because scalar energy can sometimes be biologically
disruptive when in 'raw' states. This information is primarily
intended for those who wish to use mobius coils as a means of
exciting Quartz crystals or Orgone Matrix Material, and you are
responsible for your own safety. By making this coil you agree not
to hold me responsible for any damages your experiments may cause to
persons or property. Mobius coils generate scalar waves. Scalar
waves can interfere with and/or damage electronics when high voltage
is put through them. For the purposes of Orgone research, low
voltages are sufficient to drive mobius coils.
Some other designs:
©2003-2005 Wizzers
Workshop |
